Izdelki za olje in (53)

Multipurpose oil for bearing, lever and joint lubrication Hydraulic oil for use in all areas in which physiologically harmless are required Compressor oil for piston compressors for prescribed oil ISO VG 100 Advantages and benefits NSF H1 registered Long economic operating times thanks to optimal additives against oxidation and ageing Good cold behaviour Resistant to cold and hot water, steam as well as disinfectants and cleaning agents For universal use due to long-term lubrication and high adhesive strength Good wear protection Tasteless and odourless Conforms to VDL requirements Operating temperature:-35 °C → +135 °C Density (20 °C):0.84 g/ml Viscosity (40 °C):100 mm²/s

Speziell geeignet zum Gewindeschneiden, Sägen, Bohren, Drehen, Fräsen, Reiben, Schaben und Stanzen. 2m Bohr- & Schneidöl ist ein Spezial-Hochleistungs-Schmieröl für alle Bearbeitungsverfahren, die hohe Anforderungen an ein Schneid- und Kühlschmiermittel stellen. Die Standzeit und Lebensdauer der Werkzeuge wird erhöht, während die Bearbeitungszeiten verkürzt und Oberflächenschäden verhindert werden. Speziell geeignet zum Gewindeschneiden, Sägen, Bohren, Drehen, Fräsen, Reiben, Schaben und Stanzen. Erhältlich in folgenden Gebindegrößen: 300 ml Aerosol 400 ml Aerosol 5 Liter Kanister 10 Liter Kanister 30 Liter Kanister Art.Nr.: 100580 Art.Nr.: 100583 Art.Nr.: 100571 Art.Nr.: 100570 Art.Nr.: 100572

PP 28 Deep with oil spout GLASS STONE:according to DIN 6094-7 USED PARTS:Food oils - Syrup - Fruits and. Produced - Cold filling PRESSURE RELIEF:The connections are suitable for internal pressure <1 bar OPENING VALUE:8 – 15 lbs/inch LOAD CAPACITY:Recommended for up to 12 months, cool, dry storage WHITE:3.6 KG/1,000 pieces PACKAGING:Box to 3,500 pieces - 20 boxes per palette

Die AAN GmbH stellt Anlagen zur Aufbereitung von Isolierölen her.

The QuellTech laser sensor family Q4 or Q5 used for these tasks is generally mounted on an arm of a rotational axis, to scan along the complete 360° angle of the internal surface in a sequence of strips. The Q4 sensors can also be used to control the weld seam tracking itself for rapid setup and ease of use. Even during a project, the range and scope of the Q Series sensor demonstrates the advantages of a modular system to quickly adapt to project needs, where the smallest system has provided fast analysis of pipes as small as 105mm. The low power, with standard communication protocols, enable battery powered systems to transmit wireless data to other systems for review and cloud back up.

The point bonded polyester fleece Cora®Dot is ideally suited for filtration of rolling oil by using of precoating agents. Weight range:40 – 150 g/m2 Thickness:0.19 – 0.53 mm Production width:up to 3,200 mm Composition:point bonded

Die Bornitrid-Öl-Dispersion besteht aus mineralischen Basis-Öl und feinen, hexagonalen Bornitrid-Partikeln. Schon geringe Mengen an HeBoLub® verbessern die Schmiereigenschaften der Öle und mindern den Verschleiß. HeBoLub® kommt z.B. bei Schwerlastgetrieben, Motoren oder in der metallverarbeitenden Industrie zum Einsatz.

Unser Ölnebelabscheider - höchste Wirksamkeit durch Drei-Stufen-Filtration

Unser festes Duschgel bietet eine milde und dennoch pflegende Reinigung für alle Hauttypen. Angereichert mit wertvoller Schafmilch, Sheabutter und Kokosnussöl reinigt es sanft und hinterlässt die Haut zart und geschmeidig. Die praktische feste Form macht es ideal für Reisen und unterwegs. hergestellt in Deutschland

BEDIA intelligent tank sensor ITS 65 is used to monitor the filling levels of oils of any kind. The sensor is able to automatically recognize and what kind of oil (hydaulic oil, engine oil etc.) is present and calibrates itself to it. The capacitative measurement principle permits measurement of levels without mechanically moving parts. This considerably increases stability and operating safety. Mechanics The new tank sensor ITS 65 is characterized by a particularly stable, but light mechanical system specially designed for “Heavy Duty Applications”. The mounting flange and measurement tube are constructed from die cast aluminium. This construction permits the insertion of tank sensors up to 1200 mm in length, without additional support on the tank floor. Analogue Output The analogue output is available as an voltage output with a range from 0 V to 10 V or as an PWM output.

Pins oder Anstecker werden bedruckt, geätzt oder geprägt. Jedes Motiv ist Herstellungsverfahren bedingt umsetzbar. Standardmäßig mit Dorn und Schmetterlingsverschluss. Mindestmenge: 100 Stück Verfahren:nach CMYK bedruckt im Offsetdruck mit Epoxydharzüberzug Material:Edelstahl Größe:25 x 11 mm

Die trennbare Kunststoff-Tauchsonde LMK 808 ist prädestiniert für Pegelmessungen im Wasser- und Abwasserbereich. Herzstück der Sonde ist ein extrem robuster, nahezu wartungsfreier kapazitiver Keramiksensor. Besonders zur Pegelmessung in Flussläufen, an Wehranlagen oder in Schleusen, wurde auf einen hohen Überspannungs- / Blitzschutz Wert gelegt. Zudem kann das Kabel bei Bedarf gegenüber Nagerverbiss geschützt werden. Zur Vereinfachung von Wartungsarbeiten oder Lagerhaltung ist der Sondenkopf von dem Kabelteil trennbar und kann somit bei Bedarf ohne aufwändige Montagearbeiten ausgetauscht werden. Merkmale: — Nenndrücke: 0 ... 1 mH2O bis 0 ... 100 mH2O — Genauigkeit: 0,25 % / 0,35 % FSO — Durchmesser 35 mm — gute Langzeitstabilität — Trennmembrane Keramik 99,9% Al2O3 — integrierter Blitzschutz 8 kA Gasentladungsableiter (8/20µs); 4 kV Surge L-L/L-E nach EN61000-4-5 Optionale Merkmale — Montagezubehör — verschiedene Dichtungsmaterialien — kundenspezifische Ausführungen

For cleaning and care of metal surfaces Dismantling rusted-in parts Protects electrical contacts Temporary corrosion protection for bare metal surfaces Elimination of squeaking noises Lubrication of friction points at moving machine parts Advantages and benefits Broad range of uses (6-fold action) Highly effective due to very good creep properties Also infiltrates strong oil and greasy soiling Good lubricating properties thanks to high oil percentage Displaces moisture Operating temperature:-30 °C ➝ +60 °C / 150 Density (20 °C):0.81 g/ml Base oil viscosity (40 °C):approx. 3 mm²/s Salt spray test:> 50 h Coefficient of friction SRV:µ = 0.09

Lubrication of valve seals, collars, O-rings, drives, piston rods and guides Lubrication of slides, slat-band and roller chains Lubrication of cutting knives as well as of needles and lifters of knitting machines Dismantling of rusted-in parts and removal of oil and greasy soiling Advantages and benefits NSF H1 registered Highly effective due to good creep properties Broad range of uses Displaces water Duolabel Clean the surfaces for optimal effect. Apply OKS 370 with a brush, drip oiler or by immersion or using a suitable automatic lubrication system locations to be lubricated. Spray on evenly OKS 371 spray. Avoid excesses. In as far as available, observe the machine manufacturer's instructions. Assess the lubrication frequency and quantity on the basis of the service conditions. Caution: Only mix with suitable lubricants. Operating temperature:-10 °C → +180 °C Density (20 °C):0.88 g/ml Viscosity (40 °C):14 mm²/s

Lubrication of closed toothed gearing Liquid lubrication of chains, joints, guides, fittings Suitable for immersion-bath, immersion-bath circulation and injection lubrication Advantages and benefits NSF H1 registered Good oxidation and ageing stability through optimal additives Cold and hot water resistant Resistant to water steam, disinfectants and cleaning agents Wide operating temperature range Shear-stable and low-foaming Good wear protection Good corrosion protection Long economic operating times MOSH-/MOAH-free Operating temperature:-30 °C → +120 °C Density (20 °C):0.86 g/ml Viscosity (40 °C):460 mm²/s FZG damage level:power level > 12

Highly adhesive lubrication of moving parts, e.g. valve spindles, piston rods, wire cables, drag cables, drive and conveyor chains, hinges and guides, at highly corrosive conditions in food processing technology Temporary corrosion protection of ferrous and non-ferrous metals, in particular in highly corrosive atmospheres, such as industrial atmospheres, outdoor weathering under roofs of semi-finished products and finished products Shipping protection of packed and unpacked machines and machine parts, apparatuses and equipment goods under extreme climatic conditions Advantages and benefits Highly adhesive oil with very good creep and lubrication properties Optimal corrosion protection through high effectiveness of the corrosion protection additive After the solvent has dried, forms a transparent, highly adhesive oil film Contains non-ferrous metal deactivator NSF H1-registered Operating temperature:-40 °C → +80 °C Density (20 °C):0.81 g/ml Viscosity (40 °C):> 21.5 mm²/s Salt spray test:> 100 h

Lubrication, cleaning and protection of bright metal surfaces, e.g. of precision machine tools, measuring equipment, mechanisms in precision mechanics and optics, of precision instruments Can be used at machine elements of all types, for example sliding parts or slideways, at threads, locks, hinges, joints, drives Versatile use over the full range of care, conservation and maintenance applications Advantages and benefits Highly effective due to good wetting, dissolving and protective ability Good creep properties Behaves neutrally with respect to plastics, elastomers and paints Good protection against corrosion-causing moisture and wetness Resin and acid-free OKS 700 is also suitable for use with the refillable Airspray system Also available as spray version OKS 701 Operating temperature:-50 °C → +100 °C Density (20 °C):0.84 g/ml Viscosity (40 °C):17.5 mm²/s

Lubrication of chains and machine elements operated outdoors Multi Oil also at higher temperatures Advantages and benefits Good lubricating properties Good creep capacity Biodegradable VOC-free Can be used up to 160°C Silicone-free Percentage of renewable raw materials > 90% Operating temperature:-5 °C → +160 °C Density (20 °C):0.92 g/ml Viscosity (40 °C):35 - 40 mm²/s

Maintenance oil for dismantling, lubrication and care of machine elements and metal surfaces. Dismantling of all seized or sticky components or machine elements, e.g. door locks, hinges, screws, bolts, bushings, cranks, linkages, valves, slide rails, cable pulls, shafts, etc. Lubrication of fine-mechanical instruments, measuring instruments, office and computer equipment etc., even at low temperatures Advantages and benefits Highly effective due to ideal combination of mineral oil and additives with solvent Broad range of uses in the complete maintenance sector Displaces moisture, protects against corrosion Cleans, maintains and lubricates Gets under rust Operating temperature:-30 °C → +60 °C/150 °C Density (20 °C):0.82 g/ml Viscosity (40 °C):3 mm²/s Coefficient of friction SRV:µ = 0.11 Wear SRV:0.003 mm³ Salt spray test:> 100 h

Lubrication of friction and rolling bearings, chains, joints or slideways at higher temperatures For conveying systems under radiation heat in painting, stoving and drying systems, travelling grates in firing systems Dry lubrication at temperatures above 200°C Lubrication of elastomers and plastics not resistant to mineral oil Advantages and benefits Highly suitable as a high-temperature lubricant Very effective due to finest, homogeneous MoS₂ distribution in the oil Resistant to water and many chemicals, fuels, lubricants and hydraulic oils For best adhesion, clean the surfaces. Best way is to clean mechanically first and then with OKS 2610/OKS 2611 universal cleaner. With a brush, drip oiler or by immersion or using a suitable automatic lubrication system, apply a sufficient quantity to the locations to be lubricated. If at all possible, avoid excess. Observe the machine manufacturer's instructions. Assess the lubrication frequency Operating temperature:up to +200 °C/+450 °C Density (20 °C):1.01 g/ml Viscosity (40 °C):108 mm²/s Four-ball test rig (welding load):2,800 N

Lubrication of valve seals, collars, O-rings, drives, piston rods and guides Lubrication of slides, slat-band and roller chains Lubrication of cutting knives as well as of needles and lifters of knitting machines Dismantling of rusted-in parts and removal of oil and greasy soiling Advantages and benefits NSF H1 registered Highly effective due to good creep properties Broad range of uses Displaces water OKS 370 is suitable for use with the OKS Airspray system Also available as spray version OKS 371 Clean the surfaces for optimal effect. Apply OKS 370 with a brush, drip oiler or by immersion or using a suitable automatic lubrication system locations to be lubricated. Spray on evenly OKS 371 spray. Avoid excesses. In as far as available, observe the machine manufacturer's instructions. Assess the lubrication frequency and quantity on the basis of the service conditions. Caution: Only mix with suitable lubricants. Operating temperature:-10 °C → +180 °C Density (20 °C):0.88 g/ml Viscosity (40 °C):14 mm²/s

For cleaning and care of metal surfaces Dismantling rusted-in parts Protects electrical contacts Temporary corrosion protection for bare metal surfaces Elimination of squeaking noises Lubrication of friction points at moving machine parts Advantages and benefits Broad range of uses (6-fold action) Highly effective due to very good creep properties Also infiltrates strong oil and greasy soiling Good lubricating properties thanks to high oil percentage Displaces moisture Also available as spray version OKS 601 Operating temperature:-30 °C ➝ +60 °C/150 °C Density (20 °C):0.81 g/ml Base oil viscosity (40 °C):approx. 3 mm²/s Salt spray test:> 50 h Coefficient of friction SRV:µ = 0.09

Drop lubrication of cutting tools at machining work on ferrous and non-ferrous metals, for example during drilling, thread cutting, sawing, milling, punching and nibbling Advantages and benefits Reduces friction and required force Permits high continuous load and higher cutting speeds Allows optimal cutting surfaces Extend tool lives through reduction in wear Neutral behaviour toward machine coatings Free of chlorine and heavy metals Low tendency to form oil mist OKS 390 is suitable for use with the OKS Airspray system Also available as spray version OKS 391Apply a sufficient quantity of OKS 390 to the tool or machining point using a brush, drip oiler or oil can. Spray on sufficiently OKS 391 spray. After use OKS 390 can be removed with OKS 2610/OKS 2611 universal cleaner. Caution: Check compatibility before using on non-ferrous metals. Density (20 °C):0.87 g/ml Viscosity (40 °C):22 mm²/s

Lubrication of chains and machine elements operated outdoors Multi Oil also at higher temperatures Advantages and benefits Good lubricating properties Good creep capacity Biodegradable VOC-free Can be used up to 160°C Silicone-free Percentage of renewable raw materials > 90% Spray version OKS 8601 Operating temperature:-5 °C → +160 °C Density (20 °C):0.92 g/ml Viscosity (40 °C):35 - 40 mm²/s

Drop lubrication of cutting tools at machining work on ferrous and non-ferrous metals, for example during drilling, thread cutting, sawing, milling, punching and nibbling Advantages and benefits Reduces friction and required force Permits high continuous load and higher cutting speeds Allows optimal cutting surfaces Extend tool lives through reduction in wear Neutral behaviour toward machine coatings Free of chlorine and heavy metals Low tendency to form oil mist Apply a sufficient quantity of OKS 390 to the tool or machining point using a brush, drip oiler or oil can. Spray on sufficiently OKS 391 spray. After use OKS 390 can be removed with OKS 2610/OKS 2611 universal cleaner. Caution: Check compatibility before using on non-ferrous metals. Density (20 °C):0.87 g/ml Viscosity (40 °C):22 mm²/s

Highly adhesive lubrication of moving parts, e.g. valve spindles, piston rods, wire cables, drag cables, drive and conveyor chains, hinges and guides, at highly corrosive conditions in food processing technology Temporary corrosion protection of ferrous and non-ferrous metals, in particular in highly corrosive atmospheres, such as industrial atmospheres, outdoor weathering under roofs of semi-finished products and finished products Shipping protection of packed and unpacked machines and machine parts, apparatuses and equipment goods under extreme climatic conditions Advantages and benefits Highly adhesive oil with very good creep and lubrication properties Optimal corrosion protection through high effectiveness of the corrosion protection additive After the solvent has dried, forms a transparent, highly adhesive oil film Contains non-ferrous metal deactivator NSF H1-registered Also available as spray version OKS 3601 Operating temperature:-40 °C → +80 °C Density (20 °C):0.81 g/ml Viscosity (40 °C):> 21.5 mm²/s Salt spray test:> 100 h

Lubrication wherever good penetration capacity is the only possibility for relubrication, for example at joints, hinges, linkages, levers and guides Lubrication of machine elements subjected to moisture, for example at conveying systems, packaging machines, automatic filling machines, etc. Chains in a dusty environment Advantages and benefits Light-coloured High lubrication effect due to optimum product formula Good creep properties, thus easy penetration even in narrow, hard-to-reach lubricating points Good lubricating and pressure absorption capacity Excellent corrosion protection Good wear protection, also in comparison to higher-viscosity oils without solid lubricants Broad range of uses in all maintenance sectors Operating temperature:-30 °C → +60 °C/150 °C Density (20 °C):0.82 g/ml Viscosity (40 °C):18 mm²/s Coefficient of friction SRV:µ = 0.08 Wear SRV:0.002 mm³ Salt spray test:> 150 h

Lubrication wherever good penetration capacity is the only possibility for relubrication, for example at joints, hinges, linkages, levers and guides Lubrication of machine elements subjected to moisture, for example at conveying systems, packaging machines, automatic filling machines, etc. Chains in a dusty environment Advantages and benefits Light-coloured High lubrication effect due to optimum product formula Good creep properties, thus easy penetration even in narrow, hard-to-reach lubricating points Good lubricating and pressure absorption capacity Excellent corrosion protection Good wear protection, also in comparison to higher-viscosity oils without solid lubricants Broad range of uses in all maintenance sectors Also available as spray version OKS 671 Operating temperature:-30 °C → +60 °C/150 °C Density (20 °C):0.82 g/ml Viscosity (40 °C):18 mm²/s Coefficient of friction SRV:µ = 0.08 Wear SRV:0.002 mm³ Salt spray test:> 150 h

Cora®Oil is an oleophilic polyster fleece and a unique technical innovation! Cora®Oil is a high quality thermally bonded polyester nonwoven and capable of separating oil and water. This allows oils to be completely filtered out of water. Another advantage: Cora®Oil can be used in all common band filters. Weight range:95-150 g/m2 Thickness:1,0-1,2 mm Oil adsorption factor:7-9,2 Composition:polyester Temperature max:120°C

Parting agent at foundry operations injection moulding, blowing and extruding processes of plastics and elastomer Avoids the sticking of e.g. adhesives and sealing excess or water wetting Sliding agent against noisy rubbing of plastics, elastomers and metals together or against each other Lubrication of cutting edges in the paper, cardboard, veneer layer and textile processing machines For easy retracting of plastic and rubber profiles, e.g. in the door and window production Advantages and benefits High efficiency because of excellent netting of the surface and building of extremely thin lubricating films Separating effect with antistatic properties Manifold applications for permanent lubrication, protection, maintaining and impregnation Neutral behaviour against plastic and elastomers Resistant against water and atmospheric influences Operating temperature:-50 °C → +200 °C Density (20 °C):0.96 - 0.97 g/ml Viscosity (25 °C):100 mm²/s